Industry News

RiChi & News Industry News FAQ

How to use the feed hammer mill, sharing tips for using feed feed grinding machine

  • Clicks:

Feed hammer mill is mainly used for crushing various feeds and various rough feeds. The purpose of feed crushing is to increase the surface area of ​​feed and adjust the particle size. Increasing the surface area improves the palatability, and it is easy to contact the digestive juice in the digestive edge, which is helpful to improve the digestibility. Better absorption of nutrients in feed. So, how to use feed hammer mill correctly?

How to use the feed hammer mill
How to use the feed hammer mill

1. The hammer mill should be fixed on the cement base for long-term operation. If the work place is frequently changed, the hammer mill and the motor should be installed on a base made of angle iron. If the hammer mill uses a diesel engine as the power, the power of the two should be matched, that is, the power of the diesel engine is slightly greater than the power of the hammer mill. The grooves of the pulleys are the same, and the outer end faces of the pulleys are on the same plane.

2. After the hammer mill is installed, check the tightening of each fastener. If it is loose, tighten it.

3. Check whether the tightness of the pulley belt is proper and whether the motor shaft and the hammer mill shaft are parallel.

4. Before starting the grinding machine, turn the rotor by hand to check whether the teeth, hammer and rotor are running flexibly and reliably, whether there is a collision in the shell, and whether the rotation direction of the rotor is consistent with the direction of the arrow on the machine. Whether the lubrication is good.

5. Do not replace the belt wheel casually, in case the rotation speed is too high to cause explosion in the crushing chamber, or the rotation speed is too low to affect the work efficiency.

6. After the grinding machine is started, idle for 2-3 minutes, and then feed it after there is no abnormal phenomenon. Materials such as iron nuggets and crushed stones should not be mixed in the raw materials.

7. Pay attention to the operation of the grinding machine at any time during work, and the feeding should be uniform to prevent blocking of stuffy cars, and do not run overload for a long time. If vibration, noise, excessive temperature of the bearing and the body, and outward spraying are found, stop the machine immediately and check the fault before continuing the work.

8. Operators should not wear gloves. They should stand on the side of the grinder when feeding to prevent debris from rebounding and hurting the face.

9. When clogging occurs, it is strictly forbidden to forcibly feed or remove feed with hands or sticks.

10. It should be run for 2-3 minutes at the end of the work. After the material in the machine is completely removed, the grinding machine and fan can be stopped.

The above is the article for you: How to use the feed hammer mill, sharing tips for using feed feed grinding machine. If you are interested in our products or project solutions, please contact us. We will give you the best product quality and the best price. Email:

Related Equipment
Related News
Animal Feed Hammer Mills...
Hammer mills are mostly impact grinders with swinging or stationary steel bars forcing ingredients against a circular sc ...08-31
Tips for Buying Wood Chippers...
Tips for buying wood chippers: ...06-10
Application Of Feed Hammer Mill In The Feed Pellet Productio...
Application Of Feed Hammer Mill In The Feed Pellet Production can use to crush crops, straw, corn, soybean, and ...03-28
Pellet feed vs. powder feed in cattle and sheep feed product...
We know that pellet feed and powder are processed by feed equipment. The powder is crushed by the feed hammer mill, and ...02-22
Is there a machine that combines a hammer mill and a granula...
No, the raw material pulverized by the hammer mill may not be suitable for moisture, so a dryer may be needed in the mid ...02-13
What is the role of the air inlet of the hammer mill?...
In crushing, the circulation of wind is very important. What is the role of the air inlet of the hammer mill? ...02-06

From Order To Delivery

Checking Order

With the sales contract, the order tracking clerk checks the models and quantities of each machine and spare parts.

Quality Test Before Delivery

Upon completion of the manufacturing of equipment, tthe quality inspector strictly checks quality of every machine with the checklist.

Check Items When Packing

Before packaging and shipment, the order tracking clerk checks the packaged items again with the packing list to avoid loss of items.

Sign the contract

Adopting international common standards for accurate design of product packaging, prevent product damage rate and the effective use of transport tools, which ensure the perfect delivery of products.

Get the minimum offer free of charge, please fill in the following information to tell us (confidential information, not open to the public)

Copyright © 2015-2021 by HENAN RICHI MACHINERY CO,LTD.All rights reserved. Tel:0086-18574103366